Where Do The Clips Go On Brake Pads? A Guide for Car Owners

If you are planning to replace your brake pads, you might be wondering where do the clips go on brake pads.

Brake pad clips are small metal pieces that attach to the brake caliper and help keep the brake pads in place.

They also prevent the pads from rattling, squeaking, or wearing out prematurely.

In this article, we will explain the function and installation of brake pad clips, as well as answer some common questions about them.

An image to illustrate my title "Where Do The Clips Go On Brake Pads"
Brake pad clips are vital for your braking system, but do you know where they go and how to install them?

Where do you put brake pad clips?

Brake pad clips are usually installed between the brake pads and the brake rotor.

They fit into slots or holes on the caliper bracket and the pad backing plate.

Depending on the type and design of your brake system, you may have different kinds of clips, such as anti-rattle clips, retaining clips, spring clips, or abutment clips.

The clips should come with your new brake pads, or you can buy them separately from an auto parts store.

To install them, you will need to remove the old brake pads and clips first, then clean and lubricate the caliper bracket and the new clips.

Then, you can insert the new clips into their proper positions and slide the new pads into them.

Make sure the clips are securely attached and aligned with the rotor.

What are the little clips on brake pads for?

The little clips on brake pads have several purposes.

They help to:

  • Push the brake pads away from the rotor when the brakes are not applied, reducing drag and improving fuel efficiency.
  • Keep the brake pads from moving or shifting inside the caliper, preventing noise and vibration.
  • Create a smooth and even surface for the brake pads to contact the rotor, enhancing braking performance and reducing wear.
  • Hold the wear indicators or sensors that alert you when your brake pads need to be replaced.

Do you need the clips on brake pads?

Yes, you need the clips on brake pads for optimal braking performance and safety.

Without the clips, your brake pads may become loose, misaligned, or damaged.

This can cause uneven braking, noise, vibration, or even brake failure.

The clips also help to extend the life of your brake pads and rotors by reducing friction and heat.

Therefore, you should always install new clips when you replace your brake pads.

Which side of brake pad goes on the inside?

Most brake pads are symmetrical and can go on either side of the caliper.

However, some brake pads have wear indicators or sensors that are attached to one side of the pad.

These indicators or sensors should go on the inside of the caliper, facing the piston.

This way, they can detect when the pad material is worn down to a certain level and trigger a warning light or sound on your dashboard.

To identify which side of the brake pad has the indicator or sensor, look for a metal tab or wire that protrudes from one side of the pad backing plate.

How to install brake pad retaining clip?

A brake pad retaining clip is a type of clip that holds the brake pad pins in place.

The pins are metal rods that go through holes on the caliper bracket and the pad backing plate.

They secure the pads to the caliper and allow them to slide in and out when applying or releasing the brakes.

To install a brake pad retaining clip, you will need to:

  • Remove the old clip by prying it off with a screwdriver or pliers.
  • Clean and lubricate the pin and the hole on the caliper bracket.
  • Insert one end of the pin into the hole on one side of the bracket.
  • Slide the new clip onto the pin until it snaps into place.
  • Insert the other end of the pin into the hole on the other side of the bracket.
  • Repeat for the other pin and clip.

Conclusion

Brake pad clips are essential components of your braking system that help keep your brake pads in place and prevent noise, vibration, wear, and damage.

They also improve your braking performance and fuel efficiency by pushing the pads away from the rotor when not in use.

When replacing your brake pads, you should always install new clips as well.

To do so, you will need to follow some simple steps and make sure you use the right type and size of clips for your vehicle.

If you have any questions or doubts about installing brake pad clips, you should consult a professional mechanic or refer to your owner’s manual for guidance.